Each vessel has been designed with mooring arrangements such that ropes and wires of recommended strength can help it moor safely alongside a berth, floating platform, buoy or jetty. Fundamentally a vessel has to be positioned alongside a jetty or a berth, between mooring buoys, to a mooring buoy, to another ship or barge and then made fast using her own anchors, mooring lines or shorelines.
If you want to learn more, please visit our website.
Some very common methods of mooring are Mediterranean mooring, Baltic mooring, Running mooring, Standing mooring, Spider mooring buoys, Single-point or single buoy mooring, Conventional or multi buoy mooring, Ship to Ship Mooring
While Moored alongside a fixed or floating jetty or a sea berth there are various forces acting on the vessel such as wind, current, tide, wave action, swell, surging induced due to passing ships and trim of the vessel.
The spring, breast and head lines prevent the vessel&#;s movement against the action of these forces. The directional effect of these need not be unidirectional. It can be multi-directional or at various angles to the vessel.
The resultant direction of these forces often changes with changes in direction of onshore/offshore winds or tidal streams, currents upriver and down streams. Thus a combination of breast ropes, head ropes and spring ropes is the best method to counter these forces and keep the vessel safely alongside.
Often mixed moorings are observed as some terminals based on local conditions and experiences require vessels to use more lines than they are designed for. Thus the method in which wires in conjunction with soft ropes with different SWL and construction are used as well is termed Mixed mooring.
The simplified resultant of these forces would tend to move a vessel in the transverse or longitudinal direction with respect to the jetty. Thus spring lines prevent the longitudinal motion and the breast lines check the transverse motion.
It is always preferred to avoid mixed moorings due to variable loads and elasticity of various kinds of ropes and wires which lead to different strains or weights on the lines. This can result in excessive loads on some lines than others and eventually part them putting the vessel in danger. However, for safety reasons or in a desperate situation shipmasters or pilots may have to resort to mixed moorings.
Vessels sometimes also use the seaward anchor in conjunction with mooring lines to haul the vessel out of the jetty while casting off or while making fast the vessel alongside use the seaward anchor to assist the control of the rate of lateral movement towards the berth. This manoeuvre can be carried out with or without the assistance of tugs.
Ship to Ship transfer operation involves mooring alongside two different or same sized ships for cargo transfer. During this operation, either one of the ships is at anchor or both are underway.
The mooring arrangement depends on the size of the ships. A vessel either at anchor or stopped and maintaining a constant heading is approached by the manoeuvring ship at an angle of approach as smaller as practicable. The region of approach is usually abaft the beam of the constant heading ship.
During the approach as the manoeuvring ship comes closer, it steers a course parallel to the heading or course of the other ship and reduces the horizontal distance between ships to less than 100 metres. Once this state is achieved the manoeuvring ship uses engine and rudder movements and reduces this distance further until the fenders touch each other.
The two ships thus then make parallel contact and the lines are passed respectively as per the mooring plan. As a common practice during the approach, the wind and sea are preferred to be from ahead or at very small angles to the bow.
Single buoy or single point mooring: Often larger ships that cannot approach ports and terminals are berthed outside the port limits or in sheltered anchorages and the cargo transfer carried out with the help of Single-point or single buoy moorings.
The basic principle of the buoy is to keep the position of the vessel with respect to the buoy steady and at the same time allowing vessels to swing to wind and sea..
Often a tug is provided at the aft to keep the ship at a fixed angle and distance from the buoy. The buoy is fixed by positioning it in the centre of four anchors connected to it. The ship is made fast to the buoy with the help of a single chain or two which is secured onboard to the bow stopper.
In general, while approaching Single point or single buoy moorings weather is a major criteria in determining whether to berth the vessel or not. Calm seas with low swell and wind force below 15kts are considered favourable to make an approach. Presence of strong tidal current limits the interval for berthing and unberthing.
The headway approach has to be slow often less than while at the same time approaching at a smaller angle to the buoy and then gradually hauling in the buoy messenger rope and pulling the vessel slowly towards the buoy using engine kicks at short intervals to control and maintain headway along with mooring winches to haul in the vessel when she nears about 150-200 meters from the buoy.
For unberthing the chain is released from the bow stopper and a short kick on the engines going astern swings the bow to starboard for right-handed propellers thus clearing the vessel of the buoy. Tug&#;s assistance can also be sued to pull the vessel astern and clear it of the buoy. Know more about single point mooring here.
Conventional buoy or multi buoy mooring: In this method, the bow of the ship is secured using both her anchors whereas the stern is secured to buoy around it. In the approach firstly vessel approaches the final berthing position from forward at an angle of 90 degrees to her final direction of berthing.
The starboard anchor is then let go first at a pre-decided spot while the ship is making headway. The required amount of cable is paid and the astern propulsion too operated simultaneously to stop the vessel. Once the vessel is stopped in the water port anchor is let go and thus vessel positions her stern along the centerline bifurcating the buoys.
For aligning the vessel along this centerline port cable is paid out and starboard cable heaved in with astern propulsion. The helm and engines are to be carefully used during this manoeuvre to ensure the stern is swinging clear of any of the buoys.
During unberthing, the anchor cables are heaved in to move the vessel forward and the weight is taken on windward lines while casting off other lines to prevent swinging of the stern into the other buoys. This manoeuvre requires skill and efficient operation of the ship&#;s crew as well as of the mooring equipment as often weight of the lines can be immense.
Read on baltic mooring here.
Mediterranean mooring: For this type of mooring, a pre-calculated position is determined and approached using engine movements. The bow initially is made to cant towards the berth and the starboard anchor is let go in that position.
After this, the engines are run astern and the port anchor is let go at the designated spot. The vessel falls astern and swings to starboard. Thus vessel is held by both the anchors as it approaches the quay. Stern lines are then passed. Moorings are kept tight by using the anchor cables.
The positioning of the vessel is such that mooring is completed with around four shackles on each anchor. Often tide is used to control the drift of the vessel towards the quay while positioning it by heaving or paying out on one of the anchors. Read more on mediterranean mooring here.
Running Mooring: This manoeuvre takes a relatively short duration compared to the Mediterranean mooring and offers more control of the vessel. The vessel&#;s starboard anchor is let go at a position approximately four to five shackles from the final position of the bow and around 9 shackles paid out while moving ahead on engines.
HUAZHONG contains other products and information you need, so please check it out.
Then as she falls astern with the tide the port anchor is let go and the starboard anchor is heaved onto five shackles. This method restricts the swinging room and reduces the load on the windlass.
Standing Mooring: This is practised during crosswinds. As the vessel is stopped the port anchor is let go and with the tide around 9 shackles are paid out. The starboard anchor is let go and simultaneously port anchor heaved on.
Thus the port anchor is kept on 4 shackles being generally the flood anchor and starboard on five as it is the ebb anchor. This vessel takes longer duration and provides less control over the vessel. The load on the windlass is more as compared to running moor.
Over to you..
Do you know any other important mooring methods that can be added to this list?
Let&#;s know in the comments below.
Abhishek Bhanawat is a chief officer who has worked on various types of tankers. He specializes in Crude Oil and Product Tankers. He is highly passionate about his work and loves to sail.
Read More Articles By This Author >
Disclaimer :
The information contained in this website is for general information purposes only. While we endeavour to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk.
In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this website.
Do you have info to share with us ? Suggest a correction
Disclaimer :
The information contained in this website is for general information purposes only. While we endeavour to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk.
In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this website.
Sign Up To Get Daily Newsletters
Join over 60k+ people who read our daily newsletters
Enter here
By subscribing, you agree to our Privacy Policy and may receive occasional deal communications; you can unsubscribe anytime.
Mooring is a procedure to anchor the ship to a fixed or floating element and keep it connected during loading or unloading operations. Safe mooring must withstand several forces, such as wind, the current, the tide and waves.
We are going to review the most common kinds of mooring, what they consist of and when it is advisable to use each one of them.
Ship-to-Ship transfer means mooring two ships in parallel to transfer cargo. During this operation, one of the ships may be anchored, or both of them in movement.
The procedure consists of an anchored or stopped ship being approached by another, at the most reduced angle possible. During the approach, the manoeuvring ship comes close, seeking a parallel course, reducing the distance until the fenders are in contact.
This mooring method consists of a floating dock or buoy outside the port to handle liquid or gaseous cargo from ships like oil vessels. It is used in ports that do not have specific facilities for this sort of large ship.
The ship is tied to a buoy with the aid of one or two chains which are secured on-board at the end of the prow. This mooring operation requires favourable weather with low waves and wind.
With this mooring method, the ship&#;s prow is secured with its two anchors, while the poop is secured to a buoy. The berthing position is approached at a 90-degree angle. The starboard anchor is released at a determined location as the ship moves forward. When the ship stops, the port-side anchor is released, thereby positioning the poop along the central line bifurcating the buoys.
When there is a strong wind at port and a boat must be moored without tugboats to a dock not resistant to impact, Baltic Mooring is used. The captain or the pilot use the ship&#;s anchor and on-board cables to reduce this impact, mooring the ship such that it is berthed lengthwise to the dock.
This consists of mooring the boat in perpendicular to the dock, with the poop surface parallel the jetty. This procedure is used when there is insufficient dock space to moor the boat. It is also used when there is a ramp on the poop connecting to the hold (for example, a car carrier).
Lastly, ships sometimes use the anchor along with the mooring lines to drag the vessel outside the jetty while anchoring or de-anchoring, thus helping to control the speed of lateral movement toward the dock.
Of note in this modality are Running Mooring, which provides greater control over the ship, and Standard Mooring, used during cross winds, and which takes longer.
The company is the world’s best mooring products supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.